Still other air rifles use the locking lugs of a Weaver or Picatinny rail. 7202020 Depending on the type of rifle you have the rings may need to be mounted in a couple of different ways.
If you do not do so rust will form between the scope base and the receiver.
Mounting a rifle scope. One way is to have the rings mounted to a rail system Picatinny. You can do so by mounting the bases and rings on the rifle scope. Prior to attaching the rifle scope to it add some sizeable amount of oil to the contact surface.
Remove any filler screws in the top of your receiver with a properly fitted screwdriver. First make sure the scope is in line with the barrel. How to Mount a Rifle Scope Long-Range Rifle Shooting with Ryan Cleckner - YouTube.
8312017 When mounting a scope you must make sure its securely mounted and installed on the rifle straight and level. Catching a scope in your lap when its supposed to be on the rifle is not conducive to good accuracy. Make sure these rings will fit the mount in place and then follow these steps.
This mounting hardware involves a base. How to Mount A Scope On A Rifle. Take the bottom half of the rings and fit them over the mount then.
A gun vise of some kind and a clean well lit area. The vast majority of scope mounts will be done using. After that you need to use oil or any rust preventive and then begin mounting the bases.
Mount the base on a flat surface as it will give stability to the scope. 6172019 It is usually a best practice to mount the scope on the rifle. The higher the optic is the more force and torque will affect it during recoil.
The lower the scope is mounted and the closer it is to the axis of the bore of the rifle the more likely it is to provide the consistent sight picture required for accurate long range shooting. This is the most basic and common setup you see on hunting rifles. Second make sure the scope is square to the world.
Both the Weaver and Picatinny rails are approximately 58ths of an inch wide. With this you just lock the rings into place on the rifle where they will match with the scope. The first tool that you need to mount a rifle scope is a gun cradle.
A good gun cradle will make mounting a rifle scope much easier and help you do a better job. 4252019 There are two keys to properly mounting a scope. Since they are designed to hold firearms without damaging them they are less likely to.
It needs to be securely mounted because obviously you dont want it coming off the rifle while shooting. This of course does not apply to grooved receivers or integral WeaverPicatinny bases. Mounting Base and Lower Rings to Rifle 2.
Mount the lower half of the scope ring to base using a larger flathead screwdriver since the smaller screwdriver used to mount the bases will likely slip inside the head of the screw which is used to fasten the scope ring to the base. Take the rifle out of the cradle or vice and hold the rifle as you naturally would when aiming at a target. Mounting the scope is relatively easy as most come with 2 mounting rings that are placed over the mount.
A scope ring and base setup. This is a very common scope mounting method especially on older rifles. Lasdoloda Rifle Scope Mounts Fits 1 inch 30mm Tube Offset Cantilever Profile Scope Mount Rings for Precision Shooting Competition and Hunting 20mm Picatinny 50 out of 5.
Make sure that you have selected the right mounting system for your rifle and that the rings are the correct size diameter and height to position your scope correctly. Many modern rifles have grooves for mounting attachments or are pre-drilled for scope bases. Some air rifles use the narrower 11mm or 38th inch dovetail rail.
Piece and a scope ring that screws into the base. How to Mount a Rifle Scope Long-Range Rifle Shooting with Ryan Cleckner. The other type that is commonly seen is the screw on scope.
Adjust Eye Relief Now lay scope in the rings replace the top half of the rings and lightly tighten screws. 992018 You can move the scope fore and aft in the rings or just move the entire mount on the rail until you find the correct mounting position. When you shoot the force from the exercise can loosen some screws.
Be sure to use the same length of pull on the stock as you normally would shoot if you have an adjustable buttstock. You get the scope in line with the barrel by first getting the gun level then placing the scope directly on top. Another factor is the longevity of the scopes life.
Move the scope forwards or backwards as necessary to adjust eye relief. For the purpose of mounting the bases you need to dry and clean the attaching surface first. If you choose to mount a riflescope yourself you will need a few things first.
